飼料混合機http://www.trilink-logistics.com/蒸汽是調質時水分添加的來源，同時也是飼料淀粉糊化的熱源。因此在調質中添加一定量蒸汽，既可殺滅飼料中一部分細菌，又可以稀釋飼料中天然粘結劑，使物料中的每一微粒外部形成一層薄薄的含水層，利于物料糊化，便于制粒，從而改善了顆粒飼料質量。
Mixer quenching water vapor is added the source, but also feed gelatinized starch source. So add in a certain amount of steam tempered, can kill some bacteria feed, they can dilute the feed natural binder, so that each particle in the external material forms a thin aquifer, which will help pasting material facilitate granulation, thereby improving the quality of pellets.
飼料混合機正確的蒸汽管道設計既要保證蒸汽壓力和流量，又要有效地防止管道中的冷凝水進入調質器。汽包應盡量靠近制粒機以提高蒸汽質量，因為蒸汽質量對制粒機至關重要，純度不夠的蒸汽將導致飼料混合機堵塞或產生不符合要求的飼料，并容易出現一系列故障。適合的飽和蒸汽壓力應為0.20.4Mpa，壓力過低時，在固定的調質時間達不到調質指標；壓力過高時，蒸汽溫度也高，蒸汽通過調質器對物料的熱傳導加溫增強，容易造成物料溫度高、水分低、局部物料燒焦等，影響制粒質量。
Mixer correct steam pipeline design is necessary to ensure the steam pressure and flow, but also effectively prevent condensate pipeline entering conditioner. Drum granulator should be as close as possible to improve the quality of
steam, because steam quality for granulators essential purity is not enough steam will cause feed mixer blockage or produce does not meet the requirements of the feed, and is prone to a series of failures. Suitable saturated vapor
pressure should be 0.20.4Mpa, when the pressure is too low, at a fixed time to reach temper temper targets; the pressure is too high, the steam temperature is high, the steam through conditioner heat conduction heating materials
enhanced likely to cause material temperature, low water, local materials such as burning, affect pellet quality.
要保證飼料混合機蒸汽壓力始終達到穩定，壓力波動幅度一般不應大于0.05Mpa，而蒸汽壓力與蒸汽管路系統的設計和正確安裝是分不開的。一般原料調質前含水分12%左右，蒸汽壓力高水分少，因此，低水分物料可選壓力低些蒸汽。而調質后水分大于16.5%時，制出顆粒含水分高，不容易長時間保管；調質后水分低于15%時，制粒耗電多，耐碎率低。
To ensure Mixer vapor pressure is always stable, pressure fluctuations in general should not exceed 0.05Mpa, and the design and proper installation of the steam pressure and steam piping systems are inseparable. The raw materials are
generally precursors containing about 12% water, less water vapor pressure is high, and therefore, low moisture material optionally some steam pressure is low. After quenching water while more than 16.5%, a system of particles containing high moisture, long storage is not easy; after quenching water is less than 15%, the granulation power consumption and more resistance, chipping rate.
飼料混合機http://www.trilink-logistics.com/調質溫度是和蒸汽壓力、蒸汽用量緊密相關的，也是隨季節變化的。一般畜禽飼料調質溫度在85度左右，冬季室溫低，調質溫度應低一些，夏季室溫高，調質溫度高一些。蒸汽壓力高，物料吸收的蒸汽量少，而糊化差，適合含水分高的物料。蒸汽壓力低，物料吸收的蒸汽量多，吸收水分也多，糊化好，適合于含水分低的物料。
Mixer quenching temperature and steam pressure, steam consumption is closely related, but also changes with the seasons. Usually animal feed quenching temperature around 85 degrees, winter low temperature, quenching temperature should be lower, summer high temperature, quenching temperature higher. Steam pressure, steam less material absorption and pasting difference for containing high moisture materials. Low vapor pressure and vapor amount of material absorbed more moisture absorption and more, pasting and suitable for materials containing low moisture.