在第一次生產膩子粉或者保溫砂漿之前管理人員必須先熟悉干粉混合機的技術性能、內部構造、控制結構的使用原理。運轉期間不得離開工作地點以防發生故障而損壞機件，以保證安全生產為前提檢查干粉混合機全部連接件的堅固程度，減速器內的潤滑油油量和電器設備的完整性，然后閉合總開關通電進行空運轉試機。在空運轉試機時必須逐項試驗不可減少程序。使用中如發現機器震動異常或發出不正常怪聲立即停車檢查。在未發現不正常的響聲、軸承檔發高熱、減速器溫度直升等不良現象的情況下可投入生產。在運轉過程中如需鏟刮干粉混合機槽壁物料，應用竹木器工具切不可用手以免造成不必要的人身安全事故。
Before the first production of thermal insulation mortar putty powder or managers must be familiar with the technical performance of dry powder mixer, internal structure, control the use of the principle structure. Not to leave the workplace during the operation to prevent damage to mechanical failure, in order to ensure safety in production as a precondition to check all the connections dry mixer rugged, completeness reducer in oil and electrical equipment, lubricants, and total closure switch is powered air operation conducted test machine. When the idling test machine can not reduce the test program must be itemized. The use of machine vibration found abnormal or unusual strange noise immediately stopped issuing checks. No abnormal findings in the sound file bearing high fever, the case of helicopters and other undesirable phenomena reducer temperature can be put into production. During operation For scraping powder mixer tank wall materials, bamboo tool must not be applied by hand to avoid unnecessary personal security incidents.
應保持攪拌槳兩端軸封清潔避免造成物料發黑、變質，混合槽兩端外檔方孔應保持通暢，切勿堵塞以免起反壓力污物滲入軸心，使槽內物料發黑、變質。定期對干粉混合機的保養檢查機件、蝸輪、蝸桿、軸承、軸封等各活動部分是否轉動靈活以及磨損情況，發現缺陷應及時修復，以便干粉混合機能正常使用。減速器的潤滑采用油浸式，其儲油量必須保持在油標線上，油質必須保持清潔。如經常使用須每隔三個月換一次新油，更換時應將減速器拆洗清潔后加上新油。如停用時間較長，必須將干粉混合機全部擦干凈，并用蓬布罩好。 攪拌槳裝拆時應輕拆、穩裝、輕放避免變形損壞。操作者需要注意的是掌握設備種種事項一定要靈活運用，要明白一切都為了設備的正常運作而服務。
Agitator shaft seal should be kept clean to avoid both ends of black material, deterioration, mixing tank the outside ends of the square hole should be kept open, do not block the infiltration of dirt in order to avoid pressure from the anti-axis, so that black tank materials, deterioration . Regular maintenance checks on dry mixer parts, worm, worm, bearings, shaft seals and other moving parts are rotating flexible and wear, find defects should be repaired in order to dry the mixer can be used normally. Reducer lubrication using oil-immersed, its oil reserves must be held in the oil standard line, oil must be kept clean. As often use shall be changed every three months a new oil should be replaced after the reducer washable cleaning plus new oil. If disabling a long time, all must be clean dry mixer and cover with a tarpaulin good. Paddle should dismantle light demolition, stabilization equipment, light up to avoid distortion damage. Note that the operator control device must utilize a variety of matters, in order to understand the normal operation of all equipment and services.